Kanomax 6710 TABmaster Capture Hood User Manual User Manual

CAPTURE HOOD MODEL 6710 INSTRUCTION MANUAL Be sure to read this manual thoroughly before using the instrument. Fully underst

3 2.2 Main structure  2.3 Fabric Hood The fabric hood kit consists of a frame, and a fabric hood with four windows as shown below: 3. Inst

4 2）The figures below are provided as a reference. a. Use the mark ① and the stitching as a guide to ensure the hood position. b. Make sure the

5 3.4 Installing the Main structure To install the Main structure ①, set the bottom of the panel in the holder on the unit base ② and gently push th

6 4.2 Supplying Power with Batteries ¾ 4 AA-size batteries can be used for a power supply. ¾ Press the compartment cover lock (refer to figure ①),

7 4.3 ON/OFF 1. Getting started The LCD is displayed below for reference: 2. Shut down Press and hold 【POWER】for more than 2 seconds in any

8 z SAVE: Save the current test results. z SET: Store changes or enter into the selected option’s next level interface. z MENU: On the main screen

9 Note： 1. The instrument may turn off, when you attempt to adjust the incline settings of the instrument if the battery display is at

10 4.7 Measuring 4.7.1 Start and enter into the main interface To start measuring, go to the main interface menu as shown below: a． Test ID

11 1）“Single” measurements are individual flow measurements. When you press “START”, the instrument will begin measuring and the air flow value will

12 4.7.4 Back Pressure Compensation Measurement Mode When measuring air flow in an environment with a strong wind or turbulent flow, it will produce

Thank you for your purchasing a KANOMAX instrument. This is a precision instrument, please read this instruction manual carefully before using th

13 5.1 Test Settings （1）Press or to select “Test Settings”, and press to enter into “Test Settings”. Press

14 5.1.1 Test ID setting A Test ID consists of a group of Cycles (or Samples). A Test ID can contain up to 100 Cycles. The maximum number of Test I

15 5.1.2 Test Mode settings This setting is for change the test mode & the settings about the test modes. Refer to the steps below: ¾

16 5.1.3 Set Units of Measure for Airflow, Temperature and Atmos For available units, refer to the below chart： To change the units of measur

17 5.1.4 Actual flow, Standard flow settings This setting is for selecting Actual air flow [ACT] or Standard air flow [STD]. ¾ Under the “Test Se

18 5.2 General Settings ¾ Under “MENU”, select option 2 “General Settings”. ¾ Press to enter “General Settings” or press to return to the m

19 5.3 Data processing settings ¾ Under “MENU” select option 3 “Record Processing”. ¾ Press to select “Record Processing”. Press to

20 ¾ Press or to select option item as below. ¾ Press for 2 seconds to save the changes or press t to quit. ¾ Press

21 5.5 Print Settings Note：Before printing ensure the following: 1. Please select the factory configuration printer and printer cable. For details,

22 ¾ Press or to select the “Start ID” value. ¾ Press to save or press to quit. ¾ Press or to select the “S

Composition & Parts  Standard part: Model No. Functions 6710 Air quantity/temperature/humidity  Standard components: Items Qty Main stru

23 6.Main Specifications Items 6710 Air Flow Flow range 40～4300 m³/h Accuracy Readings ±3%± 10 m³/h（Air Flow ＞85 m³/h） Resolution 1 m³/h Temper

24 7. Common Trouble Shooting Symptom Possible causes / troubleshooting No display Check the positive/negative connections of the batteries. →Verif

25 8. Warranty and After-service 8.1 Warranty  Seller warrants the goods sold hereunder, under normal use and service as described in the operator

□CHINA SHENYANG KANO SCIENTIFIC INSTRUMENT CO., LTD. #2610, 51 Wulihe Street, Heping District, Shenyang PRC. TEL: 024-23846440 83951688 83

iATTENTIONS & NOTES The warning symbols mentioned in this manual are defined below: 〔symbol classifications〕 Danger: To Prevent Serious Injury or

ii DANGER Forbidden z Do not exposure the instrument to rain or water. …… Otherwise, it may cause an electric shock, fire or injury.

1 CONTENTS 1．Introduction ... 1

2 5.1.4 Actual flow, Standard flow settings ... 17 5.2 General settings ...

1 1．Introduction The model 6710 is used to measure the air flow at the supply and the exhaust points of an HVAC system. There are several interchan

2 2. Capture Hood Structure The capture hood consists of a fabric hood, main structure and an instrument base. The structural drawing is below: